20 TON Finger Brake DIY Builder Kit

20 TON Finger Brake DIY Builder Kit

review
5
0
5
Your Price: $269.95
In Stock
Free Shipping
Part Number:6PB20TFBA

Choose Options

20 TON Finger Brake DIY Builder Kit
Fully Welded Ready To Go Out Of The Box [+$100.00]
20 TON Finger Brake Press DIY Builder Kit

Press Brake kit comes un-assembled, you do the final assembly and welding.
Designed to fit the Harbor Freight 20 ton hydraulic press Item # 32879 & 60603. Press brake kit includes an adjustable back stop and side stop for accurate and repeatable bends. .

The top clamping bar is machined out of 4140 material and includes 5 segmented removable sections. 1", 2", 3", 4" and 9.5" long pieces. These segmented blocks can be removed and rearranged to allow bending of restricted areas on a piece of sheet metal or on an already partially formed pieces.

  • Max Bending Radius (deg.) 110
  • Max. Bending Capacity 3/8" plate
  • Max Bending Width 19.25"
  • Total width of the brake is 22.125" wide

Tools required for assembly, welder, grinder, level, small square.

It Is capable of bending mild steel in the following length and thickness.

  • 19" = Full bending width of the bottom die on anything 1/8" or thinner.
  • 15" in 3/16"
  • 12" in 1/4"
  • 5" in 3/8"

The DIY 20 ton press makes a great addition to the arbor press plates we sell HERE.


PRESS BRAKE ASSEMBLY INSTRUCTIONS

We now offer the press brake kits 100% fully welded ready to go right out of the box. This offer only applies to the continental united states as the welded assemblies no longer fit inside a flat rate USPS box and they will need to ship UPS ground. The additional shipping fees required are wrapped up in the product cost of the welded product.


5 Stars
Very nice product!
I purchased the kit version of this to help build some suspension brackets and skid plates for my '65 Mustang project. I'm just a home garage hack but having nice quality HD tools is a godsend when trying to do fabrication. The kit was very easy to assemble and I actually quite enjoyed the process. The instructions were thorough and the entire process went very smoothly. I used my TIG to make sure that the welds were nice and tight and stayed clear of the ares they weren't supposed to be. Overall effectiveness as a tool is great and it bends the 1/8" steel (4" x 4") that I'm working right now like butter. Very pleased with my purchase. I also picked up the recommended arbor plates which are also very nice.
Did you find this helpful?  1 of 1 Found Helpful
Reviewed by:  from Fort Wayne. on 3/28/2017
5
4 Stars
Nice little setup - a bit of false advertising
This is a nice little setup to get a press brake capability using an inexpensive Harbor Freight press. Seems to work pretty well. My biggest complaint is that I expected to receive a "Fully Welded Ready To Go Out Of The Box" assembly. Instead I received an assembly that still needed some welding to complete it. I don't have a good welder handy which is the whole reason I paid the extra $$ for a "fully welded assembly".
Did you find this helpful? 
Reviewed by:  from Utah. on 4/2/2017
4
5 Stars
press brake
New user all the tools are hd. Now i have to figure out all that i can do. This is related to operator use but i find it difficult to figure the measurement of the radius bend. Only suggestion i have would be the dies where cut apart. I did make an radiator over flow tank out of aluminum that turned out nice for a rookie.
Did you find this helpful? 
Reviewed by:  from Grasonville. on 8/11/2016
5
5 Stars
Great product
This brake does all advertised and more. Very happy with it. Hard to find quality these days. You guys know quality. Way to go Swag Off Road. Good job!!!
Did you find this helpful? 
Reviewed by:  from Thunder Bay Ontario Canada. on 4/6/2016
5
5 Stars
Owner/Manzanita Metal works
Great product. Easy to assemble and it works great. Spend the extra money and get the air over hydraulic jack,it is so much better.
Did you find this helpful? 
Reviewed by:  from Dewey Az. on 12/27/2015
5

Related Items

Accessories