SWAG 20 TON Press Brake Heavy Duty DIY Builder Kit

SWAG 20 TON Press Brake Heavy Duty DIY Builder Kit

Your Price: $199.95
Free Shipping
Part Number:6HDPB20TA
  • This Item Ships Using (USPS), Please Provide A Suitable Shipping Address:

Choose Options

Heavy Duty 20 TON Press Brake DIY Builder KIt
Fully Welded Ready To Go Out Of The Box [+$120.00]
Heavy Duty 20 TON Press Brake DIY Builder Kit

Press Brake kit comes unassembled, you do the final assembly and welding.
Designed to fit the Harbor Freight 20 ton hydraulic press Item # 32879
& 60603.  Press brake kit includes an adjustable back stop for accurate and repeatable bends.

The heavy duty press brake kit has the same quality construction and number of components as the standard press brake kit, however the differences are as follows.  The bottom formed channel on the HD press brake kit is cut out of high strength 3/8" thick steel and the bottom "V" die of has a total width of 4" wide x 1/4" thick to allow for easier bending of thicker material. 

  • Max Bending Radius  (deg.) 110
  • Max. Bending Capacity  5/8" plate
  • Max Bending Width 19.25"  
  • Total width of the brake is 22.125" wide

Tools required for assembly, welder, grinder, level, small square.

It Is capable of bending mild steel in the following length and thickness.

  • 19" = Full bending width of the bottom die on anything 3/16" or thinner.
  • 15" in 1/4"
  • 13" in 5/16"
  • 11" in 3/8"
  • 6" in 1/2"
  • 3" in 5/8"

The HD DIY 20 ton press makes a great addition to the arbor press plates we sell HERE.


Free shipping, how it this possible?  We recently produced a new box that allows us to fit the 12 and 20 ton press brake kits into a large flat rate USPS shipping box. 

We wrapped up the cost of shipping in the purchase price of the kit as our website shipping calculator has no idea how we can transport up to 56 lbs from Oregon to New York for $20.00.  Upon check out please provide an address that USPS delivers too.

We now offer the press brake kits 100% fully welded ready to go right out of the box. This offer only applies to the continental united states as the  Heavy Duty welded assemblies no longer fit inside a flat rate USPS box and they will need to ship UPS ground.   The additional shipping fees required are wrapped up in the product cost of the welded product. 

5 Stars
Very nice kit
This is a very well cut kit. All the pieces fit together perfectly and weld up easily. Highly recommend.
Did you find this helpful? 
Reviewed by:  from Burleson, Tx. on 10/4/2017
5 Stars
This press brake works amazing. It is definitely a product every shop should have.
Did you find this helpful? 
Reviewed by:  from Florida. on 4/16/2017
5 Stars
A must have
This was so much fun to put together. I got a nice tan because in my excitement I neglected to grab my welding jacket. Everything fit like it should and it practically built itself. I'm finding so many uses for it, I only wish I got it sooner.
Did you find this helpful? 
Reviewed by:  from Philly Pa. on 4/3/2017
5 Stars
Race shop owner fabricator
Love the press brake for bending thicker steel and aluminum that my sheet metal brake won't handle. I use it to make race seat side mount brackets to bolt directly to the car floor, because various seat makers like Sparco, Recaro, and Racetech brackets don't fit anything other than another adapter plate. Assembly was a snap, my apprentice fabricator was able to put it together and weld it without any assistance.
Did you find this helpful? 
Reviewed by:  from VA. on 4/1/2017
5 Stars
20T Heavy Duty DIY Press brake - Love it!
Was excited to receive my press and immediately got busy building it with my Miller 220V MIG. Easy to build, my welds aren't pretty but the pieces fit together perfect and in about 2 hours I was bending things. A pro could DIY it much faster but I took my time. Should not have waited so long. Fun project and a must for your HF press.
Did you find this helpful? 
Reviewed by:  from Seabeck. on 12/12/2016


Recently Viewed Items