Shopping Cart Shopping Cart - 0 item(s)/Total: $0
Metal Fabrication Tools
Jeep Products
Storage Solutions
SWAG Apparel / Decals
SWAG Gift Certificates
$0 - $24.99
$25 - $49.99
Over $50

Home > Metal Fabrication Tools  > Tubing Roller, Dies & Accessories
SWAG Tubing Roller Dies Compatible With Harbor Freight Tube Roller

SWAG Tubing Roller Dies Compatible With Harbor Freight Tube Roller

Part Number 6HFDA
review 48 Review(s)
5
Write a Review Write a Review
Your Price:
$0.00
Availability:
In Stock
Free Shipping
Choose Options
SWAG 4130 Premiun Drive Axle
Yes Please [+$20.00]
No Thanks
(4) Direct Replaement Roller Bearings
Yes Please [+$12.00]
No Thanks
Select Desired SWAG Roller Die Sets
Universal Small Round Tube Dies .50", .375", .3125", .250" [+$164.95]
.625" Round Tube Dies [+$164.95]
.750" Round Tube Dies [+$164.95]
.875" Round Tube Dies [+$164.95]
1.00" Round Tube Dies [+$164.95]
1.00" Round Tube Dies Delrin [+$164.95]
1.125" Round Tube Dies [+$164.95]
1.25" Round Tube Dies [+$164.95]
1.375" Round Tube Dies [+$164.95]
1.50" Round Tube Dies [+$164.95]
1.50" Round Tube Dies Delrin [+$164.95]
1.625" Round Tube Dies [+$164.95]
1.750" Round Tube Dies [+$164.95]
2.00" Round Tube Dies [+$164.95]
2.00" Round Tube Dies Delrin [+$164.95]
2.25" Round Tube Dies [+$164.95]
2.375" Round Tube Dies [+$164.95]
2.50" Round Tube Dies [+$164.95]
.500" & .750" Square Combination Dies [+$164.95]
1.00" Square Dies [+$164.95]
1.00" Square Dies Delrin [+$164.95]
1.25" Square Dies [+$164.95]
1.50" Square Dies [+$164.95]
1.50" Square Dies Delrin [+$164.95]
1.75" Square Dies [+$164.95]
2.00" Square Dies [+$164.95]
2.00" Square Dies Delrin [+$164.95]
V Notch Square Edge Roller Dies "Diamond Profile" Up To 1.5" Square On Edge. [+$164.95]
Universal Angle Iron Dies Up To 3/8" Wide With 1.25" Inside Leg Lengh. Works With Fin Up Or Fin Down [+$164.95]
Universal Edge Roller Dies "Flat Bar Rolled The Hard Way" Works With Mataerial That Is 1/16", 1/8", 3/16", 1/4" & 1/2" Wide. [+$164.95]
Universal Flat Plate "Smooth" Dies, Will Roll Flat Material Up To 3.0" Wide [+$164.95]
.50" Round Pipe Dies [+$164.95]
.750" Round Pipe Dies [+$164.95]
.500" & .750" Round Pipe Combination Die Delrin [+$164.95]
1.00" Round Pipe Dies [+$164.95]
1.00" Round Pipe Dies Delrin [+$164.95]
1.25" Round Pipe Dies [+$164.95]
1.25" Round Pipe Dies Delrin [+$164.95]
1.50" Round Pipe Dies [+$164.95]
1.50" Round Pipe Dies Delrin [+$164.95]
2.00" Round Pipe Dies [+$164.95]
2.00" Round Pipe Dies Delrin [+$164.95]
.375"/.500" EMT Conduit Die .577"/.706" OD. [+$164.95]
.750" EMT Conduit Die .922" OD. [+$164.95]
1.00" EMT Conduit Die 1.16" OD. [+$164.95]
1.00" X 2.00" Rectangular Die [+$164.95]
2.00" X 3.00" Rectangular Die [+$164.95]
Metric 30MM Square [+$164.95]
Metric 40MM Square [+$164.95]
Metric 20MM X 40MM Rectangle [+$164.95]
Every Die Set We Offer, All 50 different sizes and 1 Drive Axle = 20% Off & Free Shipping [+$6,440.00]
Quantity
Add to Gift Registry Add to Gift Registry
Email a friend Email a friend
Add to Wish List Add to Wish List
Description
SWAG Off Road's Tubing Roller Dies Compatible With Harbor Freight Tube Roller

When you purchase the Harbor Freight Tubing roller it comes with three roller die sets, 1.0" 1.5" and 2.0" round tube dies.  If you are looking for additional tubing roller dies for theHarbor Freight tubing roller and or the HULK tubing roller you have came to the right spot.

As it currently stands we have 49 different sizes of dies available.  We stock round tube dies, square dies, round pipe dies as well as a universal edge roller dies set for rolling flat bar on edge, angle iron dies and dies for rolling square on edge in a diamond shape.  These dies are compatible with our HULK tubing roller shown HERE

Each die set is 100% CNC machined out of 1018 steel for a precise fit.  Every die set includes two outer driven rollers, one center drive roller. 

The SWAG machined 4130 cromoly premium drive axle is required and must be used with our dies.  One drive axle is compatible with every dies set we produce, hence you will only need one axle regardless of how many die sets you own.

The drive axles as well as the center drive rollers are now broached and keyed.  Using the a key way will eliminate the hassle of constantly tightening the set screws and trying to keep the "wobble" out of the center drive roller. 

The drive axle has 4 machined flats for the crank wheel which increases the grip and reduces premature wear.

The bearings that are shipped with the HF tubing roller have ~ a 20% failure rate.  We now offer factory direct replacements, a set of (4) for just $12.00.  The true cost of not finishing your project due to the bearings coming apart is far more expensive that $12.00, consider it "Project Completion Insurance".  Another additional bonus is you no longer need to constantly swap bearings from die set to die set, as you are able to leave the bearings installed in the non drive rollers so they are always set up for the next job.

We currently offer the dies in the following configurations round tube, round pipe, square, as well as a full line unique dies for doing flat bar in edge or square in a diamond profile.  In addition we also offer a full line of Delrin dies in round tube, round pipe and square sizes.  Delrin dies are well suited for aluminum, copper, brass, and chrome finished where abrasion or scratches on the material are not acceptable.

Not sure of the difference between pipe and tube, simply put tube is measured from the outside diameter, and pipe is measured on the inside diameter of the part.  For example: 1-1/2" pipe will have an OD of 1.90", where as the 1-1/2" tubing will have an actual OD of 1-1/2" See attached pipe size table below.



Click here for an in depth detailed review along with great useful tips and tricks to mastering the HF tubing roller.


Click here for a detailed review on rolling square tubing on edge for custom bike frames by Kustomized bicycle Magazine.




Video
Customer Reviews View All Reviews
Rating Tubing roller 1" square die
 
I got the 1" square tube die and the drive axle for rolling hand rails have used it on two project so far and it has worked great very impressed. I have already purchased another die, the multiuse one and can't wait to see how that works
  Reviewed by:   from Fountain Colorado. on 8/17/2015
5/5
Rating Must be made in USA
 
I do not know for sure, but it looks like those are US made - judging by the fit and finish. The quality is excellent and rolls work well. Would you guys be able to offer case hardened dies - maybe for an extra fee? Regards, Mario
  Reviewed by:   from Good quality and excellent fit.. on 8/13/2015
5/5
Rating 1 1/4 Tube Roller Dies
 
I bought a harbor tube roller to make the bends I needed for my project. I am rolling 1 1/4 aluminum tubing that is .060 wall thickness The new drive shaft, key way, and dies worked well. The roller did a great job too in no time. I lubed the dies but still got a little scuffing on one side. I will have to experiment to determine why. Thanks Swag for helping me accomplish my Fab work.
  Reviewed by:   from Twin Falls, Idaho. on 7/24/2015
5/5
Rating Dies are awesome
 
The dies arrived quickly and in perfect shape. Very high quality. The only suggestion I would have, is to cut the key slot a little longer, just for a little extra play. You may have mentioned it somewhere on this site, but it's SUPER important to oil up the pieces to be bent! That cuts down tremendously on the wear and tear on the dies!
  Reviewed by:   from Utah. on 7/23/2015
5/5
Rating Chief engineer
 
We recently purchased the 1.25 Delrin dies for roller bending 1/8" wall aluminum tube. We needed to be able to have a somewhat presentable finish as we were building a monster dolly for a fire dept rescue boat motor. these dies worked wonderfully and we did push them to the limits with the weld on wings for the Harbor Freight tubing Roller with the power feed attachment. We were able to bend a "U" with a 28" outside to outside measurement with very little distortion to the pipe.
  Reviewed by:   from Pennsylvania. on 7/15/2015
5/5
Related Items
SWAG Tubing Roller "HULK"
SWAG Tubing Roller "HULK"
Average Rating 15 Review(s)
Your Price: $799.95
SWAG Weld On Wings For Harbor Freight Tubing Roller
SWAG Weld On Wings For Harbor Freight Tubing Roller
Average Rating 20 Review(s)
Your Price: $91.95
SWAG Electric Drive / Bottle Jack Kit For The Harbor Freight Tubing Roller
SWAG Electric Drive / Bottle Jack Kit For The Harbor Freight Tubing Roller
Average Rating 11 Review(s)
Your Price: $71.95
Tubing Roller Replacement Bearings
Tubing Roller Replacement Bearings
Average Rating 0 Review(s)
Your Price: $14.95
SWAG Tubing Roller Replacement Drive Axle
SWAG Tubing Roller Replacement Drive Axle
Average Rating 1 Review(s)
Your Price: $34.95
SWAG Dimple Dies (8) Piece Set
SWAG Dimple Dies (8) Piece Set
Average Rating 5 Review(s)
Your Price: $544.95
SWAG Machined Drive Hub
SWAG Machined Drive Hub
Average Rating 5 Review(s)
Your Price: $34.95
  
Browse Similar Items