SWAG Tubing Roller Dies Compatible With Harbor Freight Tube Roller
DRIVE AXLE, EDGE ROLLER DIES, SQUARE DIES AND ROUND DIES SHOWN ABOVE

SWAG Tubing Roller Dies Compatible With Harbor Freight Tube Roller

review
5
0
5
Your Price: $0.00
In Stock
Free Shipping
Part Number:6HFDA

Choose Options

SWAG 4130 Replacement Drive Axle
1 Kit = (4) Replacement Roller Bearings
Select Desired SWAG Roller Die Sets
Universal Small Round Tube Dies .50", .375", .3125", .250" [+$164.95]
Universal Small Round Tube Dies .50", .375", .3125", .250" Delrin [+$164.95]
.625" Round Tube Dies [+$164.95]
.750" Round Tube Dies [+$164.95]
.625" & .750" Round Tube Dies Delrin [+$164.95]
.875" Round Tube Dies [+$164.95]
.875" Round Tube Dies Delrin [+$164.95]
1.00" Round Tube Dies [+$164.95]
1.00" Round Tube Dies Delrin [+$164.95]
1.125" Round Tube Dies [+$164.95]
1.25" Round Tube Dies [+$164.95]
1.25" Round Tube Delrin [+$164.95]
1.375" Round Tube Dies [+$164.95]
1.50" Round Tube Dies [+$164.95]
1.50" Round Tube Dies Delrin [+$164.95]
1.625" Round Tube Dies [+$164.95]
1.750" Round Tube Dies [+$164.95]
2.00" Round Tube Dies [+$164.95]
2.00" Round Tube Dies Delrin [+$164.95]
2.25" Round Tube Dies [+$164.95]
2.375" Round Tube Dies [+$164.95]
2.50" Round Tube Dies [+$164.95]
.500" & .750" Square Combination Dies [+$164.95]
.500" & .750" Square Combination Dies Delrin [+$164.95]
1.00" Square Dies [+$164.95]
1.00" Square Dies Delrin [+$164.95]
1.25" Square Dies [+$164.95]
1.25" Square Delrin [+$164.95]
1.50" Square Dies [+$164.95]
1.50" Square Dies Delrin [+$164.95]
1.75" Square Dies [+$164.95]
1.75" Square Dies Delrin [+$164.95]
2.00" Square Dies [+$164.95]
2.00" Square Dies Delrin [+$164.95]
V Groove "Diamond Profile" Roller Dies Up To 1.5" Square Material On Edge [+$164.95]
V Groove "Diamond Profile" Roller Dies Up To 1.5" Square Material On Edge Delrin [+$164.95]
Edge Roller Die Small "Flat Bar Rolled The Hard Way", Works With Material That Is 1/16", 1/8", 3/16", 1/4" & 1/2" Wide [+$164.95]
Edge Roller Die Large "Flat Bar Rolled The Hard Way", Works With Material That Is 5/16", 3/8", 7/16", Wide [+$164.95]
Flat Plate "Smooth" Dies, Will Roll Flat Material Up To 3.0" Wide [+$164.95]
Flat Plate "Smooth" Dies, Will Roll Flat Material Up To 3.0" Wide Delrin [+$164.95]
.500" Round Pipe Dies [+$164.95]
.750" Round Pipe Dies [+$164.95]
.500" & .750" Round Pipe Combination Die Delrin [+$164.95]
1.00" Round Pipe Dies [+$164.95]
1.00" Round Pipe Dies Delrin [+$164.95]
1.25" Round Pipe Dies [+$164.95]
1.25" Round Pipe Dies Delrin [+$164.95]
1.50" Round Pipe Dies [+$164.95]
1.50" Round Pipe Dies Delrin [+$164.95]
2.00" Round Pipe Dies [+$164.95]
2.00" Round Pipe Dies Delrin [+$164.95]
.375" &.500" EMT Conduit Die .577"/.706" OD. [+$164.95]
.750" EMT Conduit Die .922" OD. Con [+$164.95]
1.00" EMT Conduit Die 1.16" OD. [+$164.95]
1.00" Wide X 2.00" Tall Rectangular Die [+$164.95]
1.00" Wide X 3.00" Tall Rectangular Die [+$164.95]
1.00" Wide X 2.00" Tall Rectangular Die Delrin [+$164.95]
1.00" Wide X 3.00" Tall Rectangular Die Delrin [+$164.95]
2.00" Wide X 3.00" Tall Rectangular Die [+$164.95]
Metric 20MM & 25MM Square Combinatin Die [+$164.95]
Metric 20MM Wide X 40MM Tall Rectangle [+$164.95]
Metric 30MM Square [+$164.95]
Metric 40MM Square [+$164.95]
Metric 50MM Square [+$164.95]
Hand Rail Cap Die [+$164.95]
Hand Rail Cap Die Delrin [+$164.95]
Hand Rail Cap Die Cromoly [+$264.95]
Every Die Set We Offer, All 63 different sizes and 1 Drive Axle = 20% Off & Free Shipping [+$9,000.00]
SWAG Off Road's Tubing Roller Dies Compatible With Harbor Freight Tube Roller

When you purchase the Harbor Freight Tubing roller it comes with three roller die sets, 1.0" 1.5" and 2.0" round tube dies. If you are looking for additional tubing roller dies for the Harbor Freight tubing roller and or the HULK tubing roller you have came to the right spot.

As it currently stands we have 64 different sizes of dies available. We stock round tube dies, square dies, round pipe dies as well as a universal edge roller dies set for rolling flat bar on edge, angle iron dies and dies for rolling square on edge in a diamond shape. These dies are compatible with our HULK tubing roller shown HERE

Each die set is 100% CNC machined out of 1018 steel for a precise fit. Every die set includes two outer driven rollers, one center drive roller.

The SWAG machined 4130 cromoly premium drive axle is required and must be used with our dies. One drive axle is compatible with every dies set we produce, hence you will only need one axle regardless of how many die sets you own.

The drive axles as well as the center drive rollers are now broached and keyed. Using the a key way will eliminate the hassle of constantly tightening the set screws and trying to keep the "wobble" out of the center drive roller.

The drive axle has 4 machined flats for the crank wheel which increases the grip and reduces premature wear.

The bearings that are shipped with the HF tubing roller have ~ a 20% failure rate. We now offer factory direct replacements, a set of (4) for just $12.00. The true cost of not finishing your project due to the bearings coming apart is far more expensive than $12.00, consider it "Project Completion Insurance". Another additional bonus is you no longer need to constantly swap bearings from die set to die set, as you are able to leave the bearings installed in the non drive rollers so they are always set up for the next job.

We currently offer the dies in the following configurations round tube, round pipe, square, as well as a full line unique dies for doing flat bar in edge or square in a diamond profile. In addition we also offer a full line of Delrin dies in round tube, round pipe and square sizes. Delrin dies are well suited for aluminum, copper, brass, and chrome finished where abrasion or scratches on the material are not acceptable.

Not sure of the difference between pipe and tube, simply put tube is measured from the outside diameter, and pipe is measured on the inside diameter of the part. For example: 1-1/2" pipe will have an OD of 1.90", where as the 1-1/2" tubing will have an actual OD of 1-1/2" See attached pipe size table below.



Click here for an in depth detailed review along with great useful tips and tricks to mastering the HF tubing roller.


Click here for a detailed review on rolling square tubing on edge for custom bike frames by Kustomized bicycle Magazine.


TUBE ROLLER DIES INSTALLATION INSTRUCTIONS


Looking to roll hand rail cap?  We now have a die machined out of 4130 heat treated material that will roll both the large (2.250") and small (1.750) cap rail as well as .50" wide channel on one die set.  The hand rail cap die is on the bottom of the die list above.



Click this link for a YouTube video explaining the benefits of our hand rail cap die.




5 Stars
1.625" die set is perfect.
Couldn't be happier!
Did you find this helpful? 
Reviewed by:  from Pueblo Colorado . on 9/30/2017
5
4 Stars
SWAG CAP RAIL DIES
These things are seriously beefy & I don't know how else I could have done what I needed to do rolling approximately 80' of 2.25" cap rail the hard way. Be sure to grease the grooves so the cap rail doesn't bind or gouge. That said I feel that it would be a better value to sell the two cap rail sizes separately in single groove dies for better centering of the force required to bend this stuff. It is nice to have the channel groove included, but that material is pretty basic to roll & the cap rail will really benefit from being centered. SWAG products are great for those of us who 'do'.
Did you find this helpful? 
Reviewed by:  from PHOENIX. on 9/24/2017
4
5 Stars
Owner
I ordered the Harbor Freight tubing roller and the dies for 2" square tube. I added some wings to the roller. I mounted it on a piece of 2" receiver tube and slid it in my 3 point hitch on my tractor and started rolling 2" square tube with 1/8" wall. I rolled two 14' arches with a 12" rise. My 1st one took about an hour and the 2nd 45 minutes.Totally awesome!!
Did you find this helpful? 
Reviewed by:  from Eureka. on 9/5/2017
5
5 Stars
Sculptor
I absolutely love your approach to the business of metal work. I have used the heck out of the diamond square die set. I'll be back for more! Yes, use grease on the rollers.
Did you find this helpful? 
Reviewed by:  from Colorado. on 8/30/2017
5
5 Stars
Mr.
I received these very quickly using standard delivery. I put them to use right away they work great!! I will probably buy more dies in the future.
Did you find this helpful? 
Reviewed by:  from Texas. on 8/6/2017
5

Related Items